大功率半导体激光熔覆高速钢研究

使用2kW半导体激光在工具钢表面熔覆高速钢粉末。在同轴送粉的粉末汇聚点与激光的聚焦点可获得无裂纹的熔覆层。随着激光功率的增加,熔覆层厚度和粉末利用率增加,同时基体对熔覆层的稀释率下降。获得的熔覆层的硬度达到800Hv0.3,基体硬度200Hv0.3,表明大功率半导体激光在表面熔覆领域具有很好的应用前景。     

CL－1型缓蚀剂的研制

为了阻缓高含水原油对集输管线的腐蚀，研制了ＣＬ－１型输油管线缓蚀剂。这种缓蚀剂是以两种咪唑啉衍生物与联氨为主要成分的复配药剂，运用于油水共在体系．本文介绍了该剂的室内性能评价和现场试验结果。     

防垢剂BZF－2的研制与应用

桩西油田产出原油综合含水已达６０％－７０％，原用防垢剂ＨＥＤＰ已失去有效抑制集输站结垢的性能。本工作针对结垢最严重的桩５２站的应用，研制了以有机膦化合物和聚氧乙烯醚为主成份的防垢剂ＢＺＦ－２，在室内考察了不同条件下的防垢率、腐蚀性、配伍性等性能，在桩５２站进行了为期４个月的现场试验，加量为１０．３ｍｌ／ｌ、防垢率≥９８．０％，加药设备管线的腐蚀率大大降低。     

丙烯腈－苯乙烯共聚物水解磺化产物对泥浆的稳定作用

在实验室条件下对用丙烯腈－苯乙烯共聚物在硫酸存在下的水解磺化产物（ＨＳＡＳ）处理的泥浆性能进行了评定。ＨＳＡＳ处理的泥浆有较小的滤失性，较好的耐盐和抗高温性。     

锰铜基高阻尼合金中锌量的测定──硫氰酸盐萃取分离络合滴定法

基于甲基异丁基甲酮于稀盐酸介质中定量地萃取Ｚｎ￣（２＋）与ＣＮＳ￣－形成的络阴离子。从而达到与共存的锰、镍、铝、铬的完全分离。在有氟化物、硫脲存在时Ｆｅ￣（３＋）、Ｃｎ￣（２＋）和Ａｇ￣＋也不被萃取。有机相中的锌于ＰＨ５．５“六胺”缓冲介质中返萃取回水相，用ＥＤＴＡ滴定。在文中给定的条件下锌的一次被萃取率可达９９％以上，成功地解决了锰铜基高阻尼合金中共存离子对锌量测定的干扰问题。     

顶封封隔管柱的研制与应用

中原油田近年来注水压力不断升高，井况恶化严重，为此开发了顶封封隔管柱，主要阐述了管柱工况受力特点、结构、工作原理及现场使用效果。经现场较大面积的应用证明，各项性能、技术指标达到了现场要求。     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

High temperature controlled atmosphere experiments for catalysts in a transmission electron microscope

A new transmission electron microscopy (TEM) specimen preparation procedure for high temperature experiments using a controlled atmosphere specimen holder (HTCASH) has been developed. It is designed for studying the microstructure of catalyst specimens before and after treatments in various gases. The procedure involved (1) finding a new formula for the embedding material, (2) devising a new method of making specimen supports, and (3) developing a method for removing the embedding material after the specimen has been microtomed. These techniques were then brought together to produce the ideal specimens for the HTCASH experiments. As an extra benefit, this procedure is also suitable for preparing specimens for ultrahigh resolution imaging experiments. The application of the new procedure in HTCASH experiments is illustrated through a high temperature reduction of a Co/SiO₂-923 catalyst.     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.